Pull a wire, squeeze a block of water, twist a book sideways: a solid responds to each in a different way, and each response has its own modulus. Within the elastic limit, stress is proportional to strain, and the ratio is a constant of the material.
Stress, strain and the three moduli
| Modulus | Formula | Type of deformation |
|---|---|---|
| Young's modulus Y | Y = (F/A) / (ΔL/L) | Change in length (tension or compression) |
| Bulk modulus K | K = −ΔP / (ΔV/V) | Change in volume (pressure on all sides) |
| Shear modulus G | G = (F/A) / (Δx/L) = (F/A) / θ | Change in shape (tangential force) |
All three have the unit pascal (N/m²), the same as stress, because strain has no unit. The reciprocal of the bulk modulus, 1/K, is called compressibility.
Worked numericals
Which materials have which
Liquids and gases have no shear modulus (they flow) and no Young's modulus. They have only a bulk modulus. Solids have all three. Steel has a larger Young's modulus than rubber, which makes it stiffer, even though rubber can stretch much more before breaking. Stiffness and extensibility are different things.
Poisson's ratio and relations between the moduli
When a wire is stretched, it also gets thinner. Poisson's ratio σ is the ratio of lateral strain to longitudinal strain, and for most materials it lies between 0 and 0.5.
For σ = 0.3 and Y = 2 × 10¹¹ Pa, G = Y / 2(1 + σ) = 2 × 10¹¹ / 2.6 ≈ 7.7 × 10¹⁰ Pa, close to the value for steel quoted above.
Mistakes to avoid
Using the diameter instead of the area, forgetting the minus sign in the bulk modulus (ΔV is negative under pressure), and mixing up shear strain with the length change. Our note on stress-strain curves covers the full curve and the yield point.
More solved problems
In the 2 m steel wire of the earlier example, a 100 N load stretches it by 1 mm. The energy stored is U = ½FΔL = 0.5 × 100 × 0.001 = 0.05 J. Per unit volume, it is ½ × stress × strain.
Steel has K ≈ 160 GPa. To reduce its volume by 0.5 %, ΔP = K × ΔV/V = 160 × 10⁹ × 0.005 = 8 × 10⁸ Pa, about 8000 atmospheres. Solids are very hard to compress.
Y for steel is 2 × 10¹¹ Pa and for rubber about 5 × 10⁷ Pa, so steel is 4000 times stiffer. Rubber, though, can be stretched by several hundred percent before it breaks, so it is more elastic in the everyday sense of the word, but less stiff.
A steel wire of diameter 2 mm has A = π(10⁻³)² = 3.14 × 10⁻⁶ m². With a breaking stress of 5 × 10⁸ Pa, the breaking force is 5 × 10⁸ × 3.14 × 10⁻⁶ ≈ 1571 N. That is the weight of a mass of about 160 kg.
Practice questions (with answers)
- The SI unit of Young's modulus is
(a) N (b) N/m (c) N/m² (d) dimensionless - Which of the following has no shear modulus?
(a) steel (b) copper (c) water (d) glass - The value of Poisson's ratio for most materials lies between
(a) −1 and 0 (b) 0 and 0.5 (c) 0.5 and 1 (d) 1 and 2 - Two wires of the same material have different lengths. Their Young's moduli are
(a) different (b) the same (c) inversely related (d) zero - Compressibility is the reciprocal of the
(a) Young's modulus (b) shear modulus (c) bulk modulus (d) Poisson's ratio
Show answers
- (c) N/m², the same as pascal.
- (c) water. Fluids cannot resist a shearing force at rest.
- (b) 0 and 0.5.
- (b) the same. It is a property of the material, not of the size.
- (c) bulk modulus.
Common doubts
What is the difference between stiffness and strength?
Stiffness (the modulus) tells how much a material deforms under a load. Strength (the breaking stress) tells how much load it can bear before it fails. Glass is stiff but weak in tension, while rubber is not stiff but can stretch a lot.
Until when is Hooke's law valid?
Up to the proportional limit on the stress-strain curve. Beyond it, strain grows faster than stress, and past the elastic limit the deformation becomes permanent.
Why do gases have only a bulk modulus?
Gases and liquids flow under shear, so they cannot support a shear stress at rest. They do resist compression, so only the bulk modulus is defined for them.
