Home / Mechanics / Stress-Strain Curve

Stress-Strain Curve & Elasticity

CBSEICSE
Stress: 0 MPa Strain: 0 % Elastic

The physics

In the elastic region, stress is directly proportional to strain (Hooke's law) — remove the load and the material returns to its original shape. Past the yield point, deformation becomes permanent even if the load is removed.

Hooke's law (elastic region): σ = E·ε  (E = Young's modulus, the slope)
σ = stress = F/A   ε = strain = ΔL/L₀

The wire in this simulation genuinely changes color and elongation to match the region of the curve you're in — green while still elastic, orange once permanently deformed, red as it approaches fracture at 25% strain.

Exam tip: Young's modulus is defined only from the slope of the initial linear (elastic) portion — never calculate it using stress/strain values taken from the plastic region, even though the formula σ/ε still gives a number there.

Sample data: stretching wires of different materials

Young's modulus Y = stress/strain, so extension ΔL = FL/(AY) for the same load on the same wire.

MaterialYoung's modulus YExtension ΔLStrain
Steel200 GPa1.00 mm0.05000 %
Copper120 GPa1.67 mm0.08333 %
Aluminium70 GPa2.86 mm0.14286 %
Glass70 GPa2.86 mm0.14286 %
Lead16 GPa12.50 mm0.62500 %

Conditions: wire length 2.0 m, cross-section 1.0 mm², load 100 N; typical Y values.

Notice: the same 100 N load stretches a lead wire 12.5 times more than a steel wire of the same size, so steel is far stiffer. And even for steel the strain is a tiny 0.00005%, which is why Hooke's law holds nicely in the elastic region and why you need a very long wire or a vernier to measure it.

Quick answers

What are stress and strain?
Stress is force per unit area, σ = F/A, in pascals. Strain is the fractional change in length, ε = ΔL/L, and has no unit.
What is Young's modulus?
Y = stress/strain = FL/(AΔL). The unit is the pascal and the dimensional formula is [ML⁻¹T⁻²]. Steel has Y ≈ 2×10¹¹ Pa.
What is Hooke's law for a wire?
Within the proportional limit, stress is proportional to strain. The slope of the straight part of the stress-strain curve is Young's modulus.
What do the yield point and fracture point mean?
Beyond the yield point the wire is permanently deformed (plastic region) and does not return to its original length. At fracture point it breaks.

Read the full guide: Stress, strain and Young's modulus explained

🎯 Practice Zone

Puzzle 1. 🔄 If you stretch a wire within its "elastic" region and then release the load, it returns exactly to its original length. Beyond the elastic limit, releasing the load leaves the wire permanently longer. What's physically different happening inside the material in these two regions?

In the elastic region, atoms are simply displaced slightly from their normal equilibrium spacing, still held by the same interatomic bonds — releasing the stress lets these bonds pull the atoms back to their original positions, like a stretched spring. Beyond the elastic limit, the stress becomes large enough to cause atomic planes within the material to permanently slide past each other (dislocation motion in the crystal structure) — new, different equilibrium positions form, and the material simply cannot "remember" its original atomic arrangement anymore, resulting in permanent (plastic) deformation.

Puzzle 2. 📏 Young's modulus is defined ONLY from the slope of the linear (elastic) portion of a stress-strain curve, not from any point on the curve. Why can't you simply calculate stress divided by strain at any arbitrary point in the plastic region and call that Young's modulus too?

Young's modulus specifically describes the material's elastic stiffness — how strongly it resists REVERSIBLE deformation — which is a genuinely well-defined material property only where stress and strain are proportional (Hooke's law region). In the plastic (non-linear) region, the stress-strain relationship becomes complex and depends on the material's prior deformation history, not just its current stress and strain values — dividing stress by strain there gives a number, but that number doesn't represent any single meaningful, reusable material property the way true Young's modulus does.

Puzzle 3. 🏗️ Engineers designing structures (bridges, buildings) always keep stresses well BELOW the material's elastic limit, even though the material could theoretically handle much higher loads before actually breaking. Why build in such a large safety margin?

Staying within the elastic region guarantees the structure returns to its exact original shape after any temporary load (wind, traffic, earthquakes) is removed — permanent (plastic) deformation, even if the structure doesn't immediately fail, represents unacceptable permanent damage that would accumulate and compromise safety over repeated loading cycles. Additionally, real materials have manufacturing variability, unexpected loads, and fatigue effects over time — the safety margin below the elastic limit protects against these real-world uncertainties, not just the idealized single-load scenario shown in a textbook stress-strain curve.

Puzzle 4. 🥨 A material like rubber can stretch to several times its original length and still return to that original length when released, while a metal wire permanently deforms after only a tiny percentage strain. Does rubber have a HIGHER Young's modulus than metal, since it can stretch so much more?

No — rubber actually has a MUCH LOWER Young's modulus than metal, not higher. Young's modulus measures stiffness (resistance to stretching for a given stress) — a low modulus means the material stretches easily under small stress, exactly rubber's behavior. What rubber has that metal lacks is a very large ELASTIC LIMIT (it can undergo enormous elastic strain before permanent deformation begins), a completely separate material property from stiffness. Being "stretchy" (low stiffness) and being "elastic over a large range" (high elastic limit) are two independent characteristics that happen to both apply to rubber, but neither implies the other.

Puzzle 5. 💪 Two wires of the exact same material and length, but with different cross-sectional areas, are stretched by the same absolute force F. Do they experience the same strain?

No — the thicker wire (larger area A) experiences less strain for the same applied force. Stress is force divided by area (σ=F/A), so the thicker wire has lower stress for the same F, and since strain=stress/Young's modulus (for the same material), lower stress directly means lower strain. This is exactly why doubling a support cable's cross-sectional area (not just adding a second identical cable) is a standard engineering approach to reducing strain and elongation under a fixed load.

Problem 1 (NEET level). 📘 A wire of cross-sectional area 0.0001 m² experiences a force of 1000 N. Find the stress.

σ = F/A = 1000/0.0001
σ = 1×10⁷ Pa (10 MPa)

Problem 2 (JEE Main level). 📗 The same wire, originally 2m long, elongates by 0.5mm under this load. Find the strain.

ε = ΔL/L = 0.0005/2
ε = 2.5×10⁻⁴ (a dimensionless quantity, often expressed as a percentage: 0.025%)

Problem 3 (WBJEE level). 📙 Using the stress and strain from Problems 1-2, find this wire material's Young's modulus (assuming this data point is within the elastic region).

Y = σ/ε = (1×10⁷)/(2.5×10⁻⁴)
Y = 4×10¹⁰ Pa (40 GPa — a plausible value for a moderately stiff metal wire, though softer than high-grade steel)

Problem 4 (CBSE Class 11 level). 📕 Find the elastic potential energy stored per unit volume of this wire, using the stress and strain values above.

u = ½ × σ × ε = ½ × (1×10⁷) × (2.5×10⁻⁴)
u = 1250 J/m³

Problem 5 (JEE Advanced style). 📓 A different wire of the SAME material (Y=4×10¹⁰ Pa) but length 3m and area 0.0002 m² is stretched by a 2000N force. Find its elongation.

ΔL = FL/(AY) = (2000×3)/[(0.0002)(4×10¹⁰)]
ΔL = 0.75 mm
Notice this wire has double the area of the original but experiences a proportionally larger force (2000N vs 1000N) and longer length (3m vs 2m) — Young's modulus stays a fixed material property throughout, letting us predict this new wire's behavior directly.
🔬
1660

Robert Hooke discovers that a spring's extension is directly proportional to the applied force ("as the extension, so the force") — the foundational linear relationship now known as Hooke's law, underlying the entire elastic region of stress-strain behavior.

📐
1727

Leonhard Euler begins developing the mathematical theory of elastic beam bending, extending simple spring behavior into a rigorous framework for analyzing structural elements under load.

🎓
1807

Thomas Young formally defines and names the elastic modulus that now bears his name, providing a general, material-independent way to quantify stiffness — one number capturing the essential elastic response of any given material.

🏗️
19th century

Stress-strain analysis becomes indispensable to the rapidly industrializing world — critical to the safe design of railway bridges, steam engines, and the first steel-framed buildings, as engineering shifted from empirical trial-and-error toward rigorous predictive calculation.

🚀
20th–21st century

Modern materials science extends stress-strain analysis to advanced composites, aerospace alloys, and even biological tissues (bone, tendon) — the same fundamental Hooke's law and Young's modulus framework, established over three centuries ago, remains the essential starting point for understanding material behavior under load.