Home / Electricity & Magnetism / LCR Resonance

Series LCR Circuit & Resonance

JEEWBJEE
Z: 0 Ω I: 0 A Phase φ: 0° f₀: 0 Hz

The physics

In a series LCR circuit, inductive and capacitive reactances have opposite phase effects — one makes current lag the voltage, the other makes it lead. At resonance they exactly cancel, leaving only resistance to oppose the current.

Impedance: Z = √[R² + (X_L − X_C)²]   X_L = ωL, X_C = 1/ωC
Resonant frequency: f₀ = 1 / (2π√(LC))  (Z = R minimum, I = V/R maximum here)
Phase angle: tan φ = (X_L − X_C) / R

The phasor diagram on the right always closes correctly — the resultant of V_R, V_L and V_C phasors equals the applied voltage V, since this simulation solves the actual impedance triangle rather than approximating it.

Exam tip: a common JEE/WBJEE question gives two of R, L, C and the resonant frequency, asking for the third — just invert f₀ = 1/(2π√(LC)) directly, no need to compute impedance at all.

Sample data: resistance controls how sharp the resonance is

With L and C fixed, the resonant frequency does not change. Only the quality factor Q = (1/R)√(L/C) and the bandwidth Δf = R/(2πL) change.

Resistance RResonant frequency f₀Quality factor QBandwidth Δf
2 Ω503.3 Hz15.831.8 Hz
5 Ω503.3 Hz6.379.6 Hz
10 Ω503.3 Hz3.2159.2 Hz
20 Ω503.3 Hz1.6318.3 Hz
50 Ω503.3 Hz0.6795.8 Hz

Conditions: series LCR, L = 10 mH, C = 10 μF. f₀ = 1/(2π√LC).

Notice: f₀ stays at 503.3 Hz for every resistance, but cutting R by a factor of 10 makes the resonance 10 times sharper (Q goes from 0.6 to 6.3). A radio tuner is the same idea: a high-Q circuit picks one station and rejects the neighbours.

🎯 Practice Zone

Puzzle 1. ⚡ At resonance, the impedance of an LCR circuit is at its minimum (Z=R), yet the voltages across L and C individually can be much larger than the source voltage. How can a part of a circuit have more voltage than the whole source supplies?

V_L and V_C are exactly out of phase with each other (180° apart) at resonance, so while each individually can be huge, they cancel each other out almost entirely when combined — the net reactive voltage is zero, leaving only V_R to match the source voltage. This "voltage magnification" is a real, sometimes dangerous effect in resonant circuits (and is precisely how radio tuning circuits amplify a chosen frequency).

Puzzle 2. 📻 How does a radio's tuning dial actually select one station out of the many frequencies arriving simultaneously at the antenna?

Turning the dial changes the capacitance (or sometimes inductance) in an LCR circuit, shifting its resonant frequency f₀=1/(2π√LC). At resonance, the circuit responds strongly (high current) to that one specific frequency while barely responding to all others — effectively filtering out everything except the tuned station.

Puzzle 3. 🔄 Below resonance, current lags... no wait — below resonance, is the circuit more capacitive or more inductive in overall behavior?

Below resonance, X_C > X_L (capacitive reactance dominates), so the circuit behaves overall capacitively — current leads voltage. Above resonance, X_L > X_C, and the circuit behaves inductively — current lags voltage. Exactly at resonance, the two reactances cancel completely, and current and voltage are perfectly in phase.

Puzzle 4. 📊 A "sharp" (high Q-factor) resonance curve is desirable for radio tuning but would be a problem for an audio amplifier meant to handle a range of frequencies. Why?

High Q means a very narrow bandwidth — the circuit responds strongly only to a tiny range of frequencies right around resonance, which is exactly what you want for isolating one radio station. But audio spans a wide range of frequencies (roughly 20 Hz to 20 kHz) that all need to pass through with similar strength — a sharp, narrow resonance would badly distort the sound by favoring only a thin slice of that range.

Puzzle 5. 🔋 Does resonant frequency depend on the resistance R in the circuit at all?

No — f₀=1/(2π√LC) has no R in it at all. Resistance affects how sharp the resonance peak is (via the Q-factor) and how much current flows at resonance, but never shifts where the peak occurs. This is a frequently tested, easy-to-overlook fact — changing R reshapes the resonance curve without moving it left or right.

Problem 1 (NEET level). 📘 Find the resonant frequency of an LCR circuit with L=0.5 H and C=20 μF.

f₀ = 1/(2π√(LC)) = 1/(2π√(0.5 × 20×10⁻⁶)) = 50.33 Hz

Problem 2 (JEE Main level). 📗 For the same circuit with R=50 Ω, find the Quality factor Q.

Q = (1/R)√(L/C) = (1/50)√(0.5/20×10⁻⁶) = 3.16

Problem 3 (WBJEE level). 📙 Find the bandwidth of the resonance curve for the same circuit.

Bandwidth = f₀/Q = 50.33/3.16 = 15.9 Hz

Problem 4 (CBSE Class 12 level). 📕 Verify that inductive and capacitive reactance are exactly equal at the resonant frequency found in Problem 1.

X_L = 2πf₀L = 2π(50.33)(0.5) = 158.1 Ω
X_C = 1/(2πf₀C) = 1/(2π(50.33)(20×10⁻⁶)) = 158.1 Ω
X_L = X_C exactly — confirming resonance, where the two reactances cancel

Problem 5 (JEE Advanced style). 📓 Explain what happens to the total impedance and current at resonance, and why this makes LCR circuits useful as frequency filters.

At resonance: Z = √(R² + (X_L−X_C)²) = √(R² + 0²) = R (minimum possible impedance)
Current: I = V/Z = V/R (maximum possible current)
Since impedance is minimum (and current maximum) only at f₀, and rises sharply away from it, the circuit naturally "selects" the resonant frequency out of a mix of many frequencies — the basis of all LCR-based tuning and filtering circuits.
🔌
1826–1827

Georg Ohm establishes the relationship between voltage, current, and resistance — the foundational law that all later AC circuit analysis, including LCR resonance, builds upon.

🌀
1842–1853

Joseph Henry and later William Thomson (Lord Kelvin) study oscillating discharge in circuits containing both capacitance and inductance, discovering the natural oscillatory behavior that underlies resonance.

📡
1887–1888

Heinrich Hertz uses resonant LC circuits to generate and detect radio waves for the first time, experimentally confirming Maxwell's electromagnetic theory — the direct ancestor of every radio tuning circuit since.

📻
1890s–1900s

Guglielmo Marconi and other early radio pioneers develop practical tunable resonant circuits, allowing a receiver to be "tuned" to select one transmitting frequency out of many — the birth of selective radio reception as we know it today.

📐
Early 20th century

The complete mathematical theory of AC circuits — impedance, phasors, resonance, Q-factor — is formalized by engineers including Charles Steinmetz, whose complex-number (phasor) method for AC analysis remains the standard technique taught today.