Home / Thermodynamics / Heating Curve & Calorimetry

Heating Curve: Ice to Steam

CBSEICSE
Temperature: 0 °C Heat added: 0 J —

The physics

Heating a substance doesn't always raise its temperature. Away from a phase change, added heat raises temperature according to specific heat capacity. During a phase change, all the added heat goes into breaking or forming molecular bonds — the latent heat — and temperature stays exactly constant until the change is complete.

Sensible heat (temperature change): Q = mcΔT
Latent heat (phase change, constant T): Q = mL
Water: c_ice ≈ 2.1 J/g°C, c_water ≈ 4.186 J/g°C, c_steam ≈ 2.0 J/g°C
L_fusion ≈ 334 J/g (at 0°C)   L_vaporization ≈ 2260 J/g (at 100°C)

Notice the melting plateau is much shorter (less heat needed) than the boiling plateau — L_vaporization is nearly 7 times larger than L_fusion, because turning liquid into gas means completely separating molecules, while melting only loosens their rigid arrangement.

Exam tip: a very common CBSE/ICSE numerical gives a mixture of heat additions across multiple phases and asks for final temperature or total heat — always identify which segment (sensible or latent) each part of the heat goes into before applying a formula.

Sample data: heat needed to turn 100 g of ice into steam

Q = mcΔT in the sloping parts and Q = mL at the flat parts, using the values on this page.

StageHeat neededShare of totalRunning total
Ice −10 °C → 0 °C2,100 J0.7 %2,100 J
Melting at 0 °C33,400 J10.9 %35,500 J
Water 0 °C → 100 °C41,860 J13.7 %77,360 J
Boiling at 100 °C226,000 J74.0 %303,360 J
Steam 100 °C → 110 °C2,000 J0.7 %305,360 J

Conditions: c_ice = 2.1, c_water = 4.186, c_steam = 2.0 J/g·°C, L_f = 334 J/g, L_v = 2260 J/g, no heat loss.

Notice: the boiling step alone takes 74% of the 305,360 J, and melting takes 11%, even though the temperature does not change in either. Heating the water from 0 °C to 100 °C needs 41,860 J, less than one fifth of what boiling it away takes.

🔍 Explore More!

Think About It 1. 🧊 If you keep heating a glass of ice water at a steady rate, the temperature stays stuck at exactly 0°C for a while (while the ice slowly melts), even though you're continuously adding heat energy the whole time. Where is all that added heat energy actually going, if not into raising the temperature?

During melting, all the added heat energy goes specifically into breaking apart the rigid, organized structure holding ice's water molecules in a fixed crystal pattern — not into speeding up the molecules' motion (which is what temperature actually measures). Only once every last bit of ice has completely melted does additional heat finally start increasing the water's temperature again. This "stuck" temperature period during a phase change is a genuinely real, measurable physics effect, not just a coincidence — melting ice always specifically stays at exactly 0°C (at normal atmospheric pressure) until the melting process is fully complete.

Think About It 2. 🫖 Once water reaches its boiling point (100°C) and starts actively bubbling and boiling, continuing to heat it further doesn't make it any hotter than 100°C — the temperature stays fixed there until all the water has boiled away. Why can't boiling water get any hotter, no matter how much more heat you add?

Exactly the same underlying reason as melting ice — once water reaches its boiling point, all additional heat energy goes specifically into completely separating water molecules from each other (turning liquid water into freely-moving steam gas), rather than into further raising the temperature. This is precisely why a pot of boiling water on a stove stays at a steady 100°C the whole time it's actively boiling away, regardless of how high you've turned up the heat — turning up the flame just makes the water boil away FASTER, not hotter.

Think About It 3. 🥵 A severe steam burn (from actual steam, not just hot water) is often considerably more dangerous and painful than a burn from boiling water at the exact same 100°C temperature. Why might steam cause worse burns than water at the identical temperature?

When steam contacts your skin and condenses back into liquid water, it releases an enormous amount of additional stored energy (called "latent heat of vaporization") directly into your skin — this is exactly the same large amount of energy that was originally needed to turn the water into steam in the first place, now being released all at once upon contact. Boiling water, at the exact same 100°C, doesn't carry this extra hidden energy reserve to release — this is precisely why steam burns are often significantly more severe than burns from boiling water at an identical temperature.

Think About It 4. ❄️ Melting a block of ice into water takes noticeably less total heat energy than boiling that same amount of water completely into steam — even though both processes are examples of the same basic "phase change" idea. Why might melting require considerably less energy than boiling?

Melting only needs to loosen ice's rigid, organized molecular structure into the more loosely-connected arrangement of liquid water — the molecules stay relatively close together and connected throughout, just in a less rigid, more mobile arrangement. Boiling requires something far more dramatic — completely separating water molecules from each other entirely, breaking essentially ALL the connections between them to create freely-moving, widely-separated steam gas. This much bigger structural change is exactly why the latent heat needed for boiling water is roughly seven times larger than the latent heat needed to melt the same amount of ice.

Think About It 5. 🏔️ At the very top of a tall mountain, water boils at a noticeably lower temperature than the usual 100°C, sometimes even below 90°C. Given everything explored in this simulation about heating curves and boiling points, what practical challenge would this create for someone trying to cook food up there?

Since boiling water on a mountain top genuinely stays at a lower, fixed temperature (rather than reaching the usual 100°C, because of the reduced air pressure at altitude), food cooked in that boiling water will cook considerably more slowly than at sea level — the water simply isn't as hot, even though it's clearly, visibly boiling away vigorously. This is precisely why experienced mountaineers and high-altitude cooks often need noticeably longer cooking times, or specialized pressure cookers (which can raise the effective boiling temperature back up), to properly cook food at high altitude.

Try It 1 (Class 9-10 level). ✏️ Find the heat needed to raise 1kg of water's temperature by 10°C (specific heat of water = 4200 J/kg°C).

Heat = mass × specific heat × temperature change = 1 × 4200 × 10
Heat = 42,000 Joules (42 kJ)

Try It 2 (Class 10 level). ✏️ Find the heat needed to melt 1kg of ice at 0°C into water at 0°C (latent heat of fusion of ice = 336,000 J/kg).

Heat = mass × latent heat = 1 × 336,000
Heat = 336,000 Joules (336 kJ) — no temperature change happens during this melting process, all this heat goes into the phase change itself

Try It 3 (Class 10 level). ✏️ Find the heat needed to boil 1kg of water at 100°C completely into steam at 100°C (latent heat of vaporization = 2,260,000 J/kg).

Heat = 1 × 2,260,000
Heat = 2,260,000 Joules (2260 kJ) — notice this is roughly 7 times more than the heat needed to melt the same mass of ice!

Try It 4 (Class 10 level). ✏️ Find the TOTAL heat needed to take 1kg of ice at 0°C all the way to boiling water at 100°C (not yet turning it into steam), using specific heat 4200 J/kg°C and latent heat of fusion 336,000 J/kg.

Step 1 (melt ice): 336,000 J
Step 2 (heat water 0°C→100°C): 1 × 4200 × 100 = 420,000 J
Total = 336,000 + 420,000 = 756,000 Joules (756 kJ)

Try It 5 (Class 10 level). ✏️ Two identical pots of boiling water are heated with a low flame and a high flame respectively. Does the high-flame pot's water reach a higher temperature than the low-flame pot's water?

No — both pots stay at exactly 100°C while actively boiling, regardless of flame strength; the higher flame simply makes the water boil away (turn to steam) faster, not hotter, since all the extra heat goes into the latent heat of vaporization rather than raising temperature further
🔬
1750s

Scottish scientist Joseph Black made the surprising discovery that melting ice absorbs a specific, measurable amount of heat energy without any change in temperature at all — a genuinely puzzling observation at the time, since scientists had previously assumed heat and temperature were essentially the same simple thing.

💡
1760s

Black coined the term "latent heat" (meaning "hidden heat") to describe this mysterious energy absorbed during melting and boiling that doesn't show up as any change in temperature — a genuinely important conceptual breakthrough that helped separate the previously-confused concepts of "heat" and "temperature" for the first time.

⚙️
1760s-1770s

Black's careful measurements of latent heat directly assisted his friend and collaborator, engineer James Watt, in dramatically improving the design of steam engines — precisely understanding how much energy is needed to convert water into steam (and back again) was genuinely essential engineering knowledge for making steam engines significantly more efficient.

🍦
Today

Understanding latent heat remains essential in countless modern applications — from designing refrigerators and air conditioners (which rely on substances repeatedly absorbing and releasing latent heat as they change phase), to food scientists studying exactly why ice cream melts the way it does, all building directly on Joseph Black's careful 18th-century laboratory observations.