Home / Electricity & Magnetism / DC Motor

DC Motor & Fleming's Left-Hand Rule

Class 10CBSE
Torque: 0 N·m —

The physics

A current-carrying coil in a magnetic field feels a turning force (torque) — but that torque would reverse direction every half rotation without a trick: the split-ring commutator reverses the current at exactly the right moment, keeping the torque always turning the coil the same way.

Torque on the coil: τ = NIAB sinθ  (θ = angle between coil plane's normal and field)
Fleming's left-hand rule: First finger = Field, seCond finger = Current, thuMb = Motion (force)

Torque is maximum when the coil plane is parallel to the field and drops to zero when the coil plane is perpendicular to it — exactly the moment the commutator needs to switch current direction to keep the spin going.

Exam tip: a common Class 10 mix-up confuses Fleming's left-hand rule (motor — force on a current-carrying conductor) with the right-hand rule (generator — induced current from motion). Left hand for motors, right hand for generators.

Sample data: torque on the coil as it turns

τ = NIAB sin θ, where θ is the angle between the normal to the coil and the magnetic field.

Angle θsin θTorque τ
0°0.0000.000 N·m
30°0.5000.200 N·m
60°0.8660.346 N·m
90°1.0000.400 N·m

Conditions: N = 100 turns, I = 2 A, coil area 0.01 m² (10 cm × 10 cm), B = 0.2 T.

Notice: the torque is zero when the coil plane is perpendicular to the field (θ = 0°) and largest (0.400 N·m) when the plane is parallel to the field. At the zero-torque position the commutator reverses the current, so the coil keeps turning in the same direction instead of stopping.

🎯 Practice Zone

Puzzle 1. 🔄 A DC motor's coil needs a "commutator" (a rotating switch that reverses current direction every half-turn), while a simple current loop in a magnetic field wouldn't need one at all to just oscillate back and forth. Why is continuous rotation specifically dependent on this current-reversing mechanism?

Without a commutator, a current loop in a magnetic field would rotate toward its equilibrium position (coil plane perpendicular to B, zero torque), overshoot slightly due to inertia, then get pulled BACK toward that same equilibrium — settling into oscillation rather than continuous rotation, much like a pendulum. The commutator's job is to reverse the current direction at exactly the moment the coil passes through this zero-torque equilibrium point, effectively "resetting" the torque to push the coil onward in the same rotational direction rather than pulling it back — this precisely timed reversal is what converts oscillation into sustained, continuous spinning.

Puzzle 2. ⚡ A spinning DC motor generates a "back-EMF" that opposes the very current driving it. Why does a well-functioning motor genuinely need this self-generated opposing voltage, rather than it being simply a wasteful inefficiency to minimize?

Back-EMF is actually a critical, self-regulating safety and control feature, not pure waste. As the motor spins faster, back-EMF increases (it's proportional to angular speed), which correspondingly REDUCES the net current flowing through the coil (since net current depends on applied voltage MINUS back-EMF). This provides natural, automatic current limiting — without back-EMF, a motor's current would be limited only by its coil's small internal resistance, potentially drawing dangerously excessive current and overheating; back-EMF is precisely why a spinning motor draws much less current than a stalled (non-spinning) one at the same applied voltage.

Puzzle 3. 🔌 A stalled electric motor (one that's prevented from spinning, perhaps by a jam or overload) draws significantly MORE current than the same motor spinning normally, even though the applied voltage hasn't changed at all. Why does preventing rotation increase current draw so dramatically?

A stalled motor has zero angular speed, meaning zero back-EMF (which depends directly on rotational speed) — with no back-EMF to oppose the applied voltage, the FULL applied voltage now drives current through only the coil's small internal resistance (I=V/R, with no subtracted back-EMF term), producing much higher current than during normal spinning operation. This is exactly why stalled or jammed motors are a genuine fire and burnout hazard, and why many real motor circuits include overcurrent protection specifically designed to detect and respond to this stalled-motor current spike.

Puzzle 4. 🧲 Real DC motors use multiple coils (armature windings) arranged at different angles, rather than just the single simplified coil often shown in introductory diagrams. Why does using multiple coils produce noticeably smoother rotation than a single coil design?

A single coil's torque varies with angle (following a sine curve, dropping to exactly zero at the equilibrium point discussed in Puzzle 1) — this produces distinctly "jerky," pulsing torque as the motor spins, even with a working commutator managing the current reversal. Using multiple coils, each offset at a different angular position around the shaft, means that while one coil's torque contribution is momentarily near zero, other coils (at different angular positions) are still producing substantial torque — combining their contributions produces a much smoother, more consistent overall torque output throughout the full rotation, exactly why real motors use this multi-coil design.

Puzzle 5. 🔁 A DC motor and a DC generator are, at their core, essentially the SAME physical device — the fundamental difference is simply which direction energy flows through it. Can a single physical motor genuinely be used as a generator too, and vice versa?

Yes, genuinely — this reversibility is a real, practically important property, not just a theoretical curiosity. If you supply electrical current to the coil (using Fleming's left-hand rule to determine the resulting force/rotation), it acts as a motor, converting electrical energy into mechanical rotation. If you instead mechanically spin the SAME device's shaft (using Fleming's right-hand rule to determine the resulting induced current direction), the identical coil-in-magnetic-field arrangement now generates electrical current, acting as a generator. This exact reversibility is precisely why regenerative braking in electric vehicles works — the same motor that drives the wheels can run in reverse as a generator during braking, recovering kinetic energy back into the battery.

Problem 1 (NEET level). 📘 A 100-turn coil (area 0.01m²) carries 2A current in a 0.5T field, with its plane parallel to the field (maximum torque position). Find the torque.

τ = NIAB·sinθ = (100)(2)(0.01)(0.5)·sin(90°)
τ = 1.0 N·m (maximum, since the coil plane parallel to B corresponds to θ=90° between the normal and B)

Problem 2 (JEE Main level). 📗 Find the torque for the same coil when it has rotated to θ=45° from this maximum-torque position.

τ = (100)(2)(0.01)(0.5)·sin(45°)
τ = 0.707 N·m (reduced from the maximum, as expected)

Problem 3 (WBJEE level). 📙 The same coil spins at 50 rad/s. Find the back-EMF generated.

ε_back = NBAω = (100)(0.5)(0.01)(50)
ε_back = 25 V

Problem 4 (CBSE Class 12 level). 📕 The motor is connected to a 12V supply with coil resistance 2Ω, and generates the 25V back-EMF impossible — let's instead find current when back-EMF is a more modest 5V.

I = (V − ε_back)/R = (12 − 5)/2
I = 3.5 A

Problem 5 (JEE Advanced style). 📓 Using the same motor (V=12V, R=2Ω), find the stalled current (motor not spinning, zero back-EMF), and compare to the running current from Problem 4.

I_stalled = V/R = 12/2 = 6.0 A
Compared to the running current of 3.5 A (Problem 4), the stalled current is significantly higher — vividly confirming Puzzle 3's explanation of why a jammed or stalled motor draws dangerously more current than one spinning normally.
🧲
1821

Michael Faraday demonstrates the first primitive electric motor — a wire carrying current continuously rotating around a magnet, converting electrical energy into mechanical motion for the first time in recorded history.

🔧
1830s

Multiple inventors, including William Sturgeon and Thomas Davenport, develop increasingly practical DC motor designs incorporating the commutator mechanism, essential for achieving genuinely continuous, sustained rotation.

⚙️
1873

Zénobe Gramme develops a significantly improved DC motor/generator design (the Gramme ring armature), reportedly discovered partly by accident when two of his DC generators, connected together, caused one to spontaneously spin as a motor — a striking early practical demonstration of motor-generator reversibility.

🏭
Late 1800s–1900s

DC motors become foundational to early industrial machinery, electric streetcars, and elevators — though AC induction motors (not requiring a commutator at all) would eventually dominate many large-scale industrial applications due to their simpler, more robust design.

🚗
Present day

DC motor principles remain essential in countless modern applications, from small battery-powered devices to electric vehicle drivetrains — with regenerative braking (exploiting the exact motor-generator reversibility discussed in Puzzle 5) now standard in electric and hybrid vehicles.