A conductor moving through a magnetic field develops a voltage across its ends, with no battery connected. That voltage is the motional EMF. It is what drives generators, and the minus sign in Lenz's law decides which way the induced current flows. This post focuses on the numericals that appear most often: the sliding rod, the rotating rod, the changing-flux coil and eddy currents.
Motional EMF of a moving rod
Take a straight rod of length l moving with speed v at right angles to a uniform magnetic field B (and perpendicular to its own length). The free electrons in the rod feel a magnetic force, they drift to one end, and an electric field builds up until the two forces balance. The EMF across the rod is:
The same result follows from Faraday's law. If the rod slides on rails, the area of the loop grows at the rate l v, so the flux changes at the rate B l v, which is exactly the EMF.
Lenz's law and energy
The induced current always flows in the direction that opposes the change producing it. For the sliding rod, the induced current feels a magnetic force that opposes the rod's motion, so you must keep pushing. The mechanical work you do is the electrical energy that appears in the circuit. If it were the other way round, the rod would speed up by itself and we would get energy for nothing.
Worked numericals
Eddy currents
When a solid piece of metal sits in a changing flux, circulating currents form inside it. These eddy currents also obey Lenz's law, so they oppose the change. They heat the metal (induction cooktops use this) and they brake moving metal (the braking system of some trains and the damping of a galvanometer). To cut the wasted heating in transformer cores, we build them from thin insulated laminated sheets so that large loops cannot form.
More solved problems
A bar magnet's north pole moves towards a coil. The flux through the coil increases, so the coil produces a field that opposes it, making the face towards the magnet behave like a north pole. Seen from the magnet's side, that means an anticlockwise current.
A 0.2 m rod moves at 5 m/s in 0.5 T and is part of a loop of 2 Ω. ε = 0.5 × 0.2 × 5 = 0.5 V, I = 0.25 A, F = 0.5 × 0.25 × 0.2 = 0.025 N. The rod will slow down unless an external force of 25 mN acts on it.
The flux through a 50-turn coil of resistance 10 Ω changes by 4 × 10⁻³ Wb. The charge that flows is Q = NΔΦ/R = 50 × 4 × 10⁻³ / 10 = 0.02 C, regardless of how fast the change happens.
Practice questions (with answers)
- The motional EMF in a rod of length l moving with velocity v perpendicular to a field B is
(a) B l / v (b) B l v (c) B v / l (d) B l v² - Lenz's law is a consequence of the conservation of
(a) charge (b) momentum (c) energy (d) mass - If the speed of a rod in a field is doubled, the power needed to move it at that speed becomes
(a) 2 times (b) 4 times (c) 8 times (d) unchanged - Eddy currents in a transformer core are reduced by
(a) using a thicker core (b) using laminated sheets (c) increasing the current (d) using a longer core - A rod 1 m long rotates at 10 rad/s about one end in a field of 0.2 T. The EMF between the ends is
(a) 0.1 V (b) 1 V (c) 2 V (d) 10 V
Show answers
- (b) B l v.
- (c) energy.
- (b) 4 times, since P = ε²/R ∝ v².
- (b) using laminated sheets.
- (b) 1 V, since ½ × 0.2 × 10 × 1² = 1 V.
Common doubts
Is the EMF in the aeroplane wing a real voltage?
Yes, there is a potential difference between the wingtips. But you cannot draw current from it unless a closed circuit exists, and a voltmeter moving with the plane would read zero, because its leads also cut the field.
Does Lenz's law mean the induced current stops the change?
No, it only opposes the change. The flux still changes. If the opposition were complete, no induced current would remain to oppose anything.
Why does a magnet fall slowly through a copper tube?
As it falls, it changes the flux through each ring of the tube and induces eddy currents. These currents produce a field that opposes the magnet's motion, and the magnet reaches a slow terminal speed.
What is the difference between motional EMF and transformer EMF?
In motional EMF, the conductor moves in a steady field. In transformer EMF, the conductor is at rest and the field changes with time. Faraday's law covers both through the change in flux.
