Most students learn Gauss's law as a statement and then freeze when a numerical asks for the field of a charged wire. The law itself is short. The skill is in choosing the right imaginary surface, called the Gaussian surface, so that the integral does itself.

Field of a charged shell: zero inside, kQ/r² outside

The law in one line

Φ = ∮ E · dA = q_enclosed / ε₀,   ε₀ = 8.854 × 10⁻¹² C²/N m²

Only the charge inside the surface counts. Charges outside affect the field on the surface, but they contribute zero net flux. Gauss's law is always true, but it is useful for finding E only when the charge has enough symmetry to make E constant over the surface.

Flux warm-up: a charge of 8.854 nC at the centre of a cube. Φ = 8.854 × 10⁻⁹ / 8.854 × 10⁻¹² = 1000 N m²/C through the whole cube, so each face gets 1000/6 ≈ 167 N m²/C.

1. Charged spherical shell

Take a sphere as the Gaussian surface, with the same centre as the shell. By symmetry, E is radial and equal everywhere on it, so Φ = E × 4πr².

Outside (r ≥ R): E = kQ/r²   |   Inside (r < R): E = 0

For Q = 10 μC and R = 0.2 m: at r = 0.5 m, E = 9 × 10⁹ × 10⁻⁵ / 0.25 = 3.6 × 10⁵ N/C. At the surface (r = 0.2 m), E = 2.25 × 10⁶ N/C. Anywhere inside, E = 0. Outside the shell, it behaves exactly like a point charge at the centre.

2. Infinite line charge

For a long wire with linear charge density λ, use a coaxial cylinder of radius r and length l. The field is radial, so only the curved surface contributes: E × 2πrl = λl/ε₀.

E = λ / (2πε₀r) = 2kλ/r

For λ = 2 μC/m at r = 10 cm, E = 2 × 9 × 10⁹ × 2 × 10⁻⁶ / 0.1 = 3.6 × 10⁵ N/C. Field falls as 1/r, slower than the 1/r² of a point charge.

3. Infinite plane sheet

With surface charge density σ, use a small cylinder piercing the sheet. The field leaves through both flat ends: E × 2A = σA/ε₀.

E = σ / 2ε₀   (independent of distance)

For σ = 3 μC/m², E = 3 × 10⁻⁶ / (2 × 8.854 × 10⁻¹²) ≈ 1.69 × 10⁵ N/C, on either side, no matter how far you go. This surprises people, but an infinite sheet really has no length scale to dilute the field.

4. Conductor surface

Inside a conductor, E = 0, and all charge lies on the surface. Just outside, the field is twice that of a thin sheet of the same density:

E = σ / ε₀

The difference of the factor 2 is a favourite exam question. A sheet has charge on both sides of its field; a conductor has field only on the outside.

Summary table

Charge distributionGaussian surfaceField
Point charge or shell (outside)SpherekQ/r²
Shell (inside)Sphere0
Infinite lineCoaxial cylinder2kλ/r
Infinite sheetPillboxσ/2ε₀
Conductor surfacePillboxσ/ε₀

Try it yourself

Gauss Law & Equipotentials Electric Field Lines Electric Dipole Field