You push a heavy almirah and nothing happens. Push harder and it suddenly starts to slide, and then it is easier to keep it moving than it was to start it. That whole story is friction, and it is behind some of the most common numericals in Class 11: blocks on floors, blocks on inclines, cars on curves and cars stopping on a road.

The block stays at rest until the incline passes the angle of repose, then it slides

Static, kinetic and limiting friction

Friction is the contact force that opposes (or tries to oppose) the relative sliding between two surfaces. There are three cases you must separate:

fs ≤ μs N   |   flimiting = μs N   |   fk = μk N

Static friction adjusts itself to match the applied force, up to a maximum (the limiting value μsN). Once the body slides, the friction drops to the kinetic value μkN, which is smaller (μk < μs). That is exactly why it is easier to keep the almirah moving than to start it.

Surfacesμsμk
Wood on wood0.500.30
Steel on steel (dry)0.740.57
Rubber on dry concrete1.00.80
Ice on ice0.100.03

Angle of friction and angle of repose

If you slowly raise one end of a plank carrying a block, the block starts to slide at the angle where the component of weight along the plane equals the limiting friction: mg sin θ = μs mg cos θ. The angle is called the angle of repose:

tan θ = μs

The same angle is found by a handy trick: no matter what the mass of the block is, it slides at the same angle, because the mass cancels from both sides.

Worked numericals

Block on the floor: A 10 kg block, μs = 0.4 and μk = 0.3. The limiting friction is 0.4 × 10 × 9.8 = 39.2 N. A push of 30 N does not move it (static friction is then 30 N, not 39.2 N). A push of 50 N does. Now the friction is the kinetic value 0.3 × 98 = 29.4 N, so a = (50 − 29.4)/10 = 2.06 m/s².
Angle of repose: For μs = 0.577, θ = tan⁻¹(0.577) = 30°. A block placed on a plane tilted less than 30° stays at rest, and above 30° it slides.
Sliding down an incline: A block slides on a 37° incline with μk = 0.3. a = g(sin θ − μ cos θ) = 9.8 × (0.602 − 0.3 × 0.799) = 9.8 × 0.362 = 3.55 m/s². Without friction it would have been 9.8 × 0.602 = 5.9 m/s².
Stopping a car: A car moving at 20 m/s locks its wheels on a road with μk = 0.7. The deceleration is μg = 6.86 m/s², and the stopping distance is v²/(2μg) = 400/13.72 = 29.2 m. The mass of the car does not appear in the answer.

More solved problems

Problem 1: Maximum speed on a flat curve
A car goes round a flat curve of radius 50 m and μs = 0.5. The static friction provides the centripetal force, so μmg = mv²/R and v = √(μgR) = √(0.5 × 9.8 × 50) = 15.7 m/s, or 56 km/h. On a wet road with μ = 0.2 the limit drops to 9.9 m/s.
Problem 2: Block on a 30° incline
A 5 kg block on a 30° incline with μk = 0.2 slides with a = 9.8 × (0.5 − 0.2 × 0.866) = 3.20 m/s². The friction force on it is 0.2 × 5 × 9.8 × 0.866 = 8.5 N, acting up the slope.
Problem 3: Does the area of contact matter?
A 2 kg brick rests on its largest face and then on its smallest face, on the same table. The limiting friction is μsmg in both cases. The laws of friction say it does not depend on the apparent area of contact.

Practice questions (with answers)

  1. The force of friction between two surfaces depends on
    (a) the area of contact   (b) the normal reaction and the nature of surfaces   (c) the speed of the body   (d) the volume of the body
  2. For the same pair of surfaces, the coefficient of kinetic friction is
    (a) greater than μs   (b) equal to μs   (c) less than μs   (d) always zero
  3. A body of mass 2 kg on a rough horizontal surface (μs = 0.5) is pulled with 5 N. The friction acting is
    (a) 10 N   (b) 9.8 N   (c) 5 N   (d) 0
  4. The angle of repose is the angle for which tan θ equals
    (a) μk   (b) μs   (c) 1/μs   (d) sin μs
  5. If the speed of a car doubles, the braking distance for a fixed μ becomes
    (a) 2 times   (b) 4 times   (c) 8 times   (d) same
Show answers
  1. (b) the normal reaction and the nature of the surfaces.
  2. (c) less than μs.
  3. (c) 5 N. The limiting friction is 9.8 N, so the body stays at rest and static friction equals the applied force.
  4. (b) μs.
  5. (b) 4 times, since d ∝ v².

Common doubts

Is friction always a bad thing?

No. Without friction, you could not walk, grip a pen, or stop a car. It is the force that makes everyday motion possible. We reduce it only in machines, where it wastes energy and wears the parts.

Why is rolling friction smaller than sliding friction?

A rolling wheel does not slide at the contact point, so there is no kinetic friction at the contact point. The small resistance comes from the slight deformation of the wheel and the surface.

Does static friction always equal μsN?

No. That value is only the maximum (limiting) value. Below it, static friction is exactly equal to the applied force, whatever that force is. This is the most common mistake in friction numericals.

In which direction does friction act on a car accelerating forward?

Forward. The tyres push backwards on the road, and by Newton's third law the road's static friction pushes the car forward. It is the force that accelerates the car.

Try it yourself

Friction Types Pulley & Inclined Plane Circular Motion & Banking