A pn junction diode lets current pass in one direction and almost blocks it in the other. Class 12 books describe this in words, but the actual shape of the I-V curve comes from one short equation. Once you know it, the knee voltage, the tiny reverse current and the "current doubles for every 18 mV" fact all fall out of the same formula.

The current stays near zero until about 0.6 V, then climbs exponentially

The diode equation

For an ideal junction at absolute temperature T, the current for an applied voltage V is given by the Shockley equation:

I = I₀ ( eV / (n VT) − 1 )   |   VT = kT / q

Here I₀ is the reverse saturation current (a property of the diode, from picoamps to nanoamps for silicon), n is the ideality factor (between 1 and 2) and VT is the thermal voltage. At room temperature (300 K), VT = (1.38 × 10⁻²³ × 300)/(1.6 × 10⁻¹⁹) = 25.85 mV, which is why textbooks quote about 26 mV.

What the equation says in the two directions

In forward bias, V is positive and a few times VT. The exponential term becomes huge and the "−1" does not matter, so I ≈ I₀ eV/nVT. The current grows exponentially with voltage. In reverse bias, V is negative and larger than about 100 mV in size. The exponential vanishes and I → −I₀. The current is tiny and nearly constant, which is the reverse saturation current.

PropertySiliconGermanium
Knee (cut-in) voltage≈ 0.6 – 0.7 V≈ 0.2 – 0.3 V
Reverse saturation current I₀pA – nA (very small)μA (much larger)
Maximum working temperatureabout 175 °Cabout 75 °C
Typical userectifiers, ICsold radio detectors

Worked numericals

Current at 0.6 V: Take I₀ = 1 pA (10⁻¹² A), n = 1 and VT = 25.85 mV. Then e0.6/0.02585 = e23.21 = 1.2 × 10¹⁰, so I = 10⁻¹² × 1.2 × 10¹⁰ = 12 mA. At 0.5 V the same diode gives only 0.25 mA, about 50 times less, and at 0.3 V just 0.1 μA. That is why we say a silicon diode "switches on" near 0.6 V.
Reverse current: For V = −0.5 V, e−19.3 is of the order of 10⁻⁹, so I = I₀(10⁻⁹ − 1) ≈ −I₀ = −1 pA. Whether you apply −0.5 V or −5 V, the reverse current is the same, to a very good approximation.
The 18 mV rule: The current doubles when V increases by ΔV = VT ln 2 = 25.85 × 0.693 = 17.9 mV, and becomes ten times larger for ΔV = VT ln 10 = 59.5 mV. A silicon diode therefore moves from 1 mA to 10 mA with only about 60 mV more voltage, which is why its forward drop looks "fixed" at about 0.7 V.
Dynamic resistance: The slope of the curve is dI/dV = I/(nVT), so rd = nVT/I. At I = 5 mA, rd = 0.02585/0.005 = 5.17 Ω. The harder you drive the diode, the lower its dynamic resistance.

Using the diode in a circuit

In most board problems you do not use the exponential at all. You treat a silicon diode as a switch with a 0.7 V drop (or 0.3 V for germanium) and apply Kirchhoff's law. The equation tells you why that is a good approximation: the voltage barely changes over a thousand-fold range of current.

I = (E − VD) / R

More solved problems

Problem 1: Series resistor
A 5 V battery drives a silicon diode through a 430 Ω resistor in forward bias. I = (5 − 0.7)/430 = 10 mA. If you replace the silicon diode with germanium (0.3 V), I = (5 − 0.3)/430 = 10.9 mA, only 9 % more, even though the diode is quite different.
Problem 2: Voltage for a given current
With I₀ = 1 nA and n = 1, what voltage gives 10 mA? V = VT ln(I/I₀ + 1) = 0.02585 × ln(10⁷) = 0.02585 × 16.12 = 0.417 V. For 1 mA it is 0.357 V. The 10-times increase in current needed only about 60 mV more, as predicted.
Problem 3: Reverse-biased diode as an open switch
In the circuit above with the battery reversed, only I₀ flows. For I₀ = 1 nA through 430 Ω the drop is 0.43 μV, so almost the whole 5 V sits across the diode. This is the 'off' state.

Practice questions (with answers)

  1. The knee voltage of a silicon diode is about
    (a) 0.1 V   (b) 0.3 V   (c) 0.7 V   (d) 5 V
  2. In reverse bias the current of an ideal diode is approximately
    (a) zero always   (b) −I₀ and nearly constant   (c) proportional to V   (d) infinite
  3. If the temperature rises, the reverse saturation current
    (a) decreases   (b) increases rapidly   (c) stays the same   (d) becomes zero
  4. A p-n junction conducts well in forward bias because
    (a) the depletion layer becomes thicker   (b) the barrier is lowered and majority carriers cross   (c) minority carriers vanish   (d) the junction heats up
  5. The dynamic resistance of a diode carrying 2.6 mA at 300 K (n = 1) is about
    (a) 1 Ω   (b) 10 Ω   (c) 100 Ω   (d) 1 kΩ
Show answers
  1. (c) 0.7 V. (0.3 V is for germanium.)
  2. (b) −I₀ and nearly constant.
  3. (b) increases rapidly, roughly doubling for every 10 °C rise in silicon.
  4. (b) the external voltage lowers the barrier, so majority carriers cross in large numbers.
  5. (b) 10 Ω, since r = 25.85 mV / 2.6 mA ≈ 9.9 Ω.

Common doubts

Why does a diode not conduct below 0.7 V if the equation gives some current at every voltage?

It does give a small current: for I₀ = 1 pA, about 0.1 μA at 0.3 V. The 'knee' is the voltage where the current becomes large enough to matter (milliamps), which for silicon is near 0.6 to 0.7 V. It is a practical edge, not a sharp physical switch.

What does the ideality factor n mean?

It measures how far a real junction is from the ideal one. n = 1 means diffusion current only. When recombination in the depletion layer also matters, n moves towards 2, and the curve rises more slowly.

Why does a Zener diode behave differently in reverse bias?

At a high reverse voltage, the breakdown mechanism (Zener or avalanche) lifts the current suddenly. The simple equation does not include breakdown, so it describes only the region before it.

Does the diode equation depend on temperature?

Yes, in two ways. VT = kT/q increases with T, and I₀ rises very quickly with T. The net effect is that the forward voltage for a given current falls by about 2 mV per °C.

Try it yourself

PN Junction Diode Transistor Characteristics Energy Bands