Capacitor questions in the board exam and in NEET and JEE are scoring if you keep five formulas in your head and know which one fits which situation. They are also where students lose marks through the same few mistakes. Here are the formulas, then six numericals in the order I teach them.

Battery connected: a dielectric slab raises C, Q and the stored energy by the same factor

The five formulas

C = Q/V    C = ε₀A/d    U = ½CV² = Q²/2C = ½QV
Series: 1/C = 1/C₁ + 1/C₂ + …
Parallel: C = C₁ + C₂ + …

The unit of capacitance is the farad (F). One farad is large in practice, so you will meet microfarad (10⁻⁶ F), nanofarad and picofarad. The dimensional formula of capacitance is M⁻¹L⁻²T⁴A².

Numerical 1: parallel plates

Question: plates of area 0.02 m² are 1 mm apart in air. Find C.
Solution: C = ε₀A/d = 8.85×10⁻¹² × 0.02 / 10⁻³ = 1.77×10⁻¹⁰ F, which is about 177 pF. Even big plates give a picofarad-scale capacitor, which is why practical capacitors use thin dielectrics and rolled foils.

Numerical 2: series combination

Question: capacitors of 2 μF and 3 μF are joined in series across 120 V. Find the charge and the voltage across each.
Solution: C_eq = (2 × 3)/(2 + 3) = 1.2 μF. In series the charge is the same on each: Q = C_eq V = 1.2×10⁻⁶ × 120 = 144 μC. Then V₁ = Q/C₁ = 144/2 = 72 V and V₂ = 144/3 = 48 V. They add up to 120 V, which is your check. Notice that the smaller capacitor takes the larger voltage.

Numerical 3: parallel combination

Question: the same 2 μF and 3 μF capacitors are joined in parallel across 120 V.
Solution: C_eq = 2 + 3 = 5 μF. In parallel the voltage is the same on each, so Q₁ = 2 × 120 = 240 μC and Q₂ = 3 × 120 = 360 μC. Total charge 600 μC, which equals 5 × 120. Parallel gives a bigger capacitance, series gives a smaller one, smaller than the smallest in the group.

Numerical 4: energy stored

Question: a 10 μF capacitor is charged to 12 V. How much energy is stored?
Solution: U = ½CV² = ½ × 10×10⁻⁶ × 144 = 7.2×10⁻⁴ J = 720 μJ. Small, but released in a very short time it is enough for a camera flash. Pick the form of U that matches the data you were given: ½CV² when V is known, Q²/2C when Q is known.

Numerical 5: inserting a dielectric

A dielectric of constant K = 4 fills the space between the plates. The answer depends on whether the battery stays connected.

Battery connected (V constant): C becomes 4C, Q = CV becomes 4Q, and U = ½CV² becomes 4U. The battery supplies extra charge.
Battery disconnected (Q constant): C becomes 4C, V = Q/C falls to V/4, and U = Q²/2C falls to U/4. The energy decreases because the slab is pulled in by the field, so it is the field that does positive work, and you would have to hold it back.

This pair of cases appears again and again in entrance exams. Always read whether the battery is still connected before you write anything.

Numerical 6: charge sharing and the "lost" energy

Question: a 6 μF capacitor charged to 100 V is connected to an uncharged 3 μF capacitor. Find the common voltage and the energy lost.
Solution: Initial charge Q = 6×10⁻⁶ × 100 = 600 μC. After connecting, the same total charge spreads over 9 μF, so V = 600/9 = 66.7 V. Initial energy = ½ × 6×10⁻⁶ × 100² = 0.030 J. Final energy = ½ × 9×10⁻⁶ × (66.7)² = 0.020 J. So 0.010 J, one third of the original, is lost as heat and radiation in the connecting wire, even if the wire has almost no resistance.

A checklist before you submit

Is it series or parallel? Is the battery connected or removed? Did you convert μF to F? Do the voltages in a series chain add to the supply? If your energy increased when you inserted a dielectric with the battery removed, go back: it must fall.

Try it yourself

Parallel Plate Capacitor RC Circuit Charging & Discharging Gauss's Law & Equipotentials